While the Nerf Rhino Fire blaster is a dependable weapon, it can stop working for various reasons. In such circumstances, you’ll definitely benefit from having knowledge about why that happens.
So, what could be the reasons for nerf rhino fire not working?
The most common issues are regarding the trigger and springs. They are notorious for their weak build and jamming. A dead battery may also cause the problem. Moreover, the drum magazines jam up at times. Last but not least, your gun IC might get jumbled and cause all the problems.
However, the question of how remains. Now, we’ve laid out the issues and answers to five of them in this article.
That being said, read on to find out.
4 Reasons Your Nerf Rhino Fire is Not Working And Their Solutions
As a nerf gun enthusiast, gun malfunction can be very frustrating. You might go berserk if you are not able to troubleshoot the problem. It may become complicated like the problems of KWA ATP.
Do not worry, we got your back. Troubleshooting the Nerf Rhino Fire will be easier than before.
I have compiled the top 4 reasons why your Nerf Rhino Fire is not working. Also, don’t forget to read all about the solutions to fix those issues!
So, let’s start without wasting any more time!
Reason 1: Trigger Switch Problem
This is the most common Nerf Rhino Fire problem. The trigger gets jammed and the gun stops working.
The problem could be the spring, but it could also be the trigger switch.
RhinoFire’s trigger is supported by a little spring that can be accessed by opening the gun. This spring can break down or become corroded resulting in a trigger jam.
However, the solution is very simple and easy.
As the switch is weaker, you could try switching out the spring for a stronger one.
If a new spring doesn’t fix the problem, the switch is definitely broken.
We would recommend the orange mod longshot trigger switch. This switch is strong and does not break down easily.
Reason 2: Battery Problem
Another common Nerf Rhino Fire issue is the battery. Usually, the gun takes 6 D-size batteries to operate. It’s very common for the batteries to drain out.
Note that the gun requires at least 9V to operate properly. If the voltage goes below that, the gun will not work. Also, the battery terminals might get corroded and jammed. This will prevent electricity flow from the batteries.
The solution is straightforward. Firstly, check the voltage of the batteries. Make sure you have at least 9 Volts for operation. You can use a multimeter for this.
If you don’t have any multimeter on you, it’s high time you get one! That’s because they can be useful in so many different occasions. Here are some recommendations from my personal usage-
- If you’re looking for a budget option, try AstroAI Multimeter 2000 Counts. It’s very affordable and can give you enough flexibility while working with electrical components.
- KAIWEETS Digital Multimeter with Case is another great budget deal. It even comes with a protective case for better longevity.
- If you’re not concerned with the budget, AstroAI Digital Multimeter TRMS 6000 Counts is the power-packed one.
If the batteries are drained out, replace them with authentic D-size batteries. But if the batteries are all good, do check the battery terminals. If there are any corrosions, you can clean them up.
To clean up the battery terminals, you can use rubbing alcohol and some cloth wipes. You can brush off the rust with a metal brush and alcohol. Then you clean up using wipes.
Reason 3: Loading Magazine Problem
The nerf magazine of the Rhino Fire is notorious for being problematic. They are prone to jamming, especially the drum magazines. The nerf bullet loading system may jam out every now and then.
Your Rhino may not consistently cycle and even if the drums are empty, the barrel might get jammed.
However, as hard as the problem may seem, the solution is not that hard at all.
If the trigger gets jammed, you need to push it several times to get it unjammed. Jamming also happens if you load the nerf darts improperly.
Make sure you load your darts properly before starting the gun. If your gun gets jammed mid-round, you will need to reload the darts again.
While loading, make sure the darts are aligned with the drum mag. Otherwise, the darts might come off during shooting.
However, the best solution is to use the stick magazine. The Rhino stick magazines do not jam like the drum magazines.
But, do note that using a stick magazine will limit your loading capacity. The loading capacity will be reduced to 18 rounds per magazine from 25.
Reason 4: Circuit Board Problem
Circuit board issues are not that prevalent, but they might come up. Especially when you mess with the IC. The solders on the switch might come off if pulled harshly.
If you have accidentally peeled off any part of the board, it might need resoldering or rewiring.
However, we got the right solutions for the IC problems.
If your solders are coming off, take the help of an expert to resolder them. Do not try it by yourself unless you have tried it before. Check if all the wire connections are connected properly.
Tips on Maintaining Nerf Rhino Fire
Here are some tips and tricks that will help you maintain your Rhino Fire nerf gun.
Avoid Dry Firing:
Dry firing is when you shoot your blaster without a dart in it, which is pretty obvious. When firing a Nerf gun without a projectile in the chamber, the plunger head will strike the barrel’s post. This will cause it to chip and break.
This is especially true if you have upgraded the spring system on your Nerf gun. It’s best to avoid dry firing altogether because it puts unnecessary strain on your spring and blaster.
Avoid Storing Loaded Gun:
Don’t put your ready-to-fire blaster away. The clip’s spring will eventually wear out if you always use it fully loaded. After all, there’s no point in keeping the spring compressed and stressing it if you have no plans to use the gun anytime soon.
Identify and fix any problems At least once every six months or after any significant conflict. Be sure to inspect for damage regularly.
If your gun has any leaks, you can check it out by submerging it. Fill in the cracks and fix the broken parts. Use rags and Q-tips to wipe away dirt and grime from your pump guns.
Both spring and pump guns benefit from being kept adequately lubricated. Every few months, or after each major battle, you should apply some lubricant to the moving parts.
Hopefully, these tips will come in handy during maintenance.
Frequently Asked Questions (FAQs)
Why Is My Motorized Nerf Gun Not Working?
You need to properly set your batteries. It’s important to properly insert the batteries into the holder. See if the positive and negative terminal metal prongs are making contact with the battery holders. Still not working? Try a new set of batteries.
How Do I Fix a Nerf Gun That Doesn’t Shoot?
You can fix the issue by moving the plunger so that its air stream enters the barrel at an angle. A plunger consists of two tubes, one inside the other. When the trigger is pulled, the air is forced out of the inner tube. This happens as the outer tube is pulled back into the gun.
Are Nerf Guns Ok for 5-Year-Old?
Yes, it is okay for a 5-year-old child. In the event that you instruct your child in safe gun handling, Nerf guns are ideal for this purpose. It can be a wonderful present for a youngster. When properly shielded, the foam darts fired from a Nerf gun pose no threat to the user.
In any case, that settles it. The solutions to the problem of nerf rhino fire not working have hopefully been made clear in this article.
Finally, remember that your Nerf Rhino Fire will not work without batteries.
Plus, it would be wonderful to hear some positive feedback from you.